I’ve been 3D printing for several years now and have tested a wide variety of filaments, both good and bad. The Elegoo 4-pack of PLA filament (White, Gray, Black, and Clear) is easily one of the best I’ve used. First off, the packaging is excellent. Each spool comes vacuum-sealed with silica gel packets to keep the filament dry during shipping. I’ve been using this filament with my Flashforge Adventurer 5M, and the results have been outstanding. The filament feeds smoothly, with no tangling or snags, and adheres perfectly to the PEI build plate. The dimensional accuracy is spot-on, which is great for me since I mainly use it for functional prints. I'd also like to note that I’ve experienced zero clogs or jams during printing. I will definitely continue to use PLA from Elegoo.

I have never had issues will Elegoo filament that werent caused by my own oversight. The filament prints flawlessly and the color always turnout vibrant. It feeds and retracts perfectly through the Creality CFS and prints without issue using the standard generic PLA profile on the K-2 Plus. Elegoo will always be my go to because of its great price and quality, reliable performance.

Great product at a good price. Delivery was timely and package was placed where we instructed. No problems with the product when used and performed perfectly. Have already repeated the order twice.

I opened the sealed white filament today to do some 3d printing, it comes in a 4 KG pack black white red and blue. I attempted 5 prints and only one came out alright, not perfect but acceptable. Looking at the roll of filament right out of the box I was not impressed the way it was rolled on the spool it looked like a tangled mess so I kept a close watch over the printing process. The other 4, I had issues with stringing and poor bed adhesion so I had to stop the prints all 4 were failures. I’ve been printing with Creality’s pla and have not had any issues whatsoever. I adjusted the nozzle temperature from 200 to 195 and minimized the stringing but was still present. As far as the bed adhesion goes I clean the bed with isopropyl alcohol after every print to keep it as clean as possible, as I said earlier I’ve had no issues with Creality’s filament. Pretty disappointing to say the least, don’t think I could recommend this product to anyone with a clear conscious, I think it’s that bad. Reading the other reviews I see that others have had similar issues with this brand of filament, wish I would have read them before purchasing could have saved myself the headaches. Edit I had sent this filament back to Amazon and was contacted by Elegoo. Their customer service is exceptional they inquired what issues I had. They informed me they would like to send me replacement filament to try again. It arrived in a few days and being that I had other things going on was unable to test it out. The replacement filament is superior to the first batch I ordered. It prints without issue adheres to the bed as intended it isn’t oozing from the nozzle like the first set I received. The only issue I noticed was that there was some minimal stinging but did not affect the end product of the print. I can’t praise Elegoo enough for standing behind their product and for having such great customer service and striving for customer satisfaction. I would not hesitate to purchase purchasing their product again knowing what kind of customer service they provide.

Skip to end for original review. I'd like to restart this review saying that ELEGOO customer service is pretty great. They contacted me almost a day after I left the first review. At first, they wanted more information about what I did for troubleshooting. Then once I told them what I tried to do to fix it, they offered to fully refund me or send me a new roll of filament for replacement. I accepted the replacement hoping I could use this cheap filament. Once the new filament arrived, I spent some time cleaning the hot end of my printer and re-calibrating my auto bed leveling (CR Touch). Tried the new filament roll and it worked perfectly. I haven't had a failed print or a misprint, and I have less than 200g left on the roll. I'm not sure what changed between the first and the second roll, but I haven't had a problem since. Because this filament printed so flawlessly (albeit after the first bad roll and hours of troubleshooting) I think I'll continue to use this. My plan is to use this PLA for testing purposes, then print my final models with PETG from a different brand. As far as I can tell, this filament does exactly what it needs to. I'm not one to speak on quality, just as long as it makes a decent print. I did run into some bed adhesion issues on thin prints that lifted off of the bed, but that was fixed by a reprint and a glue stick. So far, so good ELEGOO. Thanks for caring and for trying to fix what was wrong. I hope to see more of your product in the future. ORIGINAL REVIEW: I'll start this review off with saying that I am only a hobbyist and that there is a lot I don't know. I was very excited to give this low-cost PLA a try, so I don't have to use my slightly more expensive PETG to test out my projects and designs. For this price, I was ready to make a bulk order. I only bought one roll at first. There wasn't really anything that seemed too special, or any advantage over the other brand that I mainly use. Upon printing, though, I ran into some issues. Now my setup isn't your typical 3D printer layout. I have an Ender 3 V2, which is inside of a repurposed cabinet, with my filament rolls sitting above the cabinet inside of a repurposed PC case. From the PC case, the filament has to travel about 15-20 inches through a PTFE tube (stock ender 3 bowden tube, plus a section of Capricorn ptfe bowden tube), to the printer extruder. I haven't had any issues with the printer having the ability to pull the filament all that way, but it will probably end up just wearing out my extruder motor faster. Whether all that makes sense or not, moral of the story is that my usual filaments don't have a problem being pulled such lengths. What happened with this specific filament is a different story. Usually, I'm able to press start on a print and then walk away, come back however many hours (in this case it was a 19hr print), and then have my project me done and ready to go. Now on this print, I went to check on it about 15hrs into the print, and noticed that my printer had only laid it's single first layer on the build plate, then nothing else was printed. My hot end was sitting there floating, with my extruder gear still trying to push filament through. Turns out, my extruder gear had wore a notch into the filament, and the filament would no longer be pushed through the hot end. Tried multiple times to restart the print, clear the hot end, even increase the hot end from a recommended 200C to the PETG temp of 240C to make whatever blockage there was melt. Nothing made a permanent difference. I finally gave up when I had my hot end set at 245C, and extrusion speed at 30 mm/sec. Slow and hot for PLA. Nothing would work. I would only get the first couple layers to print, then it acted like it was clogged and the extruder gear would sit there and spin. So, maybe the problem is my setup and how far away my filament is from my printer. Even though this probably isn't common to do, my usual brand of Overture hasn't had any issues, PLA or PETG. I can't comment on quality, strength, or anything else, because I couldn't get it to even print. I will try sometime on the future to see if I can come up with a solution, then change my review if I find anything. Thanks for your time.

Todo bien en general pero el blanco es un poco transparente comparado don otras marcas y tenemos que mandar más capas o relleno para que no se vea lo que hay detrás, se usó para llaveros y al usar poco material se transparentaba un poco. Fuera de ese detalle el material funciona bien no hace burbujas no se atora en el extrusor...

Genial! es tan bueno que ya hice mi segundo pedido. Lo compre para probarlo y ahora lo quiero como mi filamento principal

Muy bien filamento y bastante económico. Se imprime sin problemas y se pega muy bien a la cama. Le volveré a comprar.

Me gustó mucho. Excelente para mi impresora 3d creality k1 máx. Soporto muy bien las altas velocidades de 250mm/s. Imprimí ese dinosaurio flexible y quedo muy bien. Sin errores

Really high quality! Go for this if you care about print quality.