There's a lot of good adhesives out there, but this is my go-to for a clear, hard, crevice-filling epoxy. Fully liquid to start, begins getting thick within ten minutes, which is just what I want for working with a variety of materials and surfaces. Fully cures, clear, dry and hard, in 24 hours. At which point, whatever problem you were trying to solve, is solved. Good stuff. Recommended.

I bought a desk and the last piece was the top piece. The holes through the metal frame didn't match up. So I just placed it on top and vowed to be super careful. Didn't work and I broke my monitor. So I saw this and decided to give it a try. Tips: use gloves and keep the plunger up right. The cap didn't screw back on. This stuff worked very well. I just spread a bunch of glue on the frame and placed the board on top. I placed clips all around and when I checked it 5 hours later, it was set and didn't even wiggle a little bit. Now I don't have to worry about buying a new desk. BTW: it was hard to get both sides of the glue to come out evenly. Nonetheless, it worked.

really liked the product. for starters it’s very cheap, and it’s very strong. i had ripped my mirror off my car windshield on accident and i used this to stick it back on and worked wonderfully !

Used it for bonding an antler to knife blank. Worked well. Strong adhesion.

I needed this to hold broken aquarium glass together and to keep from cracking more. Dried quickly. Is holding well. Used it to cover sharp edges too.

Great product, great price, great service

I first acquired this epoxy to repair a custom, cast, resin, wall sculpture of a Great Blue Heron (in flight) that a visitor had removed and dropped, causing it to shatter into four pieces along its four foot wing span. Initially, I also purchased three foot long, aluminum braces to reinforce the sculpture’s wing span. To my amazement, with only a modest amount of this Gorilla-brand epoxy applied to the joints between the broken pieces — and no structural reinforcements — the entire wing span of the sculpture is fused with such strength and rigidity that I can support the entire weight of the sculpture (80 lbs.) at anywhere along the wing span without it flexing or coming apart. This is really astounding. The entire sculpture may actually be materially stronger than before the repair. For safe measure, I added a smear of the epoxy along the back side of the sculpture along all along the fracture joints. It is now so rigid and strongly bound that I can tap the tips of the wings and the entire sculpture resonates like a metal gong, which means it is, for all practical purposes, fused into a uni-body entity. Some tips: 1. There’s a plastic wand wedged between the push-rods of the dual syringe. You need to break this wand out of there to be able to fully depress the syringe. Personally, I found a wooden popsicle stick to make a much better wand for mixing the epoxy and applying it. 2. You’ll know that the epoxy components (resin and hardener) are properly mixed when you can smell a temporary stink like rotten eggs. Soon after, the epoxy will catalyze and generate heat. From that point, you have 5 minutes to apply the epoxy before it starts to thicken and set. Thus, to maximize your work time, you can start applying the epoxy as soon as your smell the pungent stink. The stink goes away as soon as the epoxy starts to set. Full strength and cure, which is when no tackiness can be felt in the epoxy, occurs at around 24 hours, 3. The epoxy has a thick consistency, like honey. It fills small gaps extremely well and will self-level to an extent, removing brush strokes and smoothing over depressions. It is clear with a very slight amber tint. It goes on clear and cures to a clear, tough-as-nails finish. 4. I recommend wearing nitrile gloves as you work with this epoxy, as if it gets on your skin, you’ll need acetone to remove it. Acetone is very effective at breaking down this epoxy before it cures. However, once it cures, the acetone will not soften or dissolve it. 5. If you want to shape or flatten the epoxy — on the back of a sculpture for example — after it sets, you can lay the side of the item with the epoxy against a polyethylene sheet on a level floor or table top. The epoxy sticks like crazy to resin, metals, wood, stone, glass, leather but will not adhere to polyethylene plastic. After the epoxy cures, you can pull away the polyethylene sheet and the epoxy will be hard and smooth like glass. It will bond strongly to 3D printed thermoplastics like PLA. 6. As long as you keep the resin and hardener separate, these components will last a surprisingly long time. Working over several days to join each fractured piece of the sculpture, I left the nozzles of the double syringe uncovered and the epoxy components easily remained viable for several days. For longer term keeping on any open syringe, just stretch a section of duct tape over the nozzles. 7. Where a really clean joint is needed, applying the epoxy to just one side and pressing the parts together will give surprisingly strong adhesion. However, for maximum strength, I recommend applying epoxy to both sides of a joint and letting a “bead” ooze out along the joint. On the cosmetic side of your project, the bead can be smoothed out before the epoxy cures. I recommend leaving the raised bead on the non-cosmetic back side of any such workpiece, and after it cures, coming back with more epoxy to smear over the bead to create a wider seam patch for maximum joint strength. The fresh epoxy adheres well to any old cured epoxy. The stuff is for certain a resin, and will practically weld any resin components into a rigid uni-body. This epoxy lives up to its brand name of being gorilla strong.

Bought this to use to glue leather strips into metal bracket claps. Works great, holds tight, dries fast.

Have been using this glue for may years and it's good to have it at home. unlike other brands, this glue can be store for a long time.

Gorilla Epoxy is my go-to adhesive! This two-part formula creates a strong, durable bond on various materials. Easy to use, it sets quickly, providing a reliable and long-lasting hold. Perfect for DIY projects and repairs. Gorilla Epoxy - my trusty solution for sturdy and lasting connections!

Lo utilicé por una recomendación de las opiniones en Amazon, para pegar metal con plástico (en este caso el imán del celular para fijarlo cuando voy manejando) y ha resistido las vibraciones y movimientos bruscos sin despegarse, por lo menos varias semanas sin problema, ya que otros se han despegado a los días, inclusive el pegamento que trae original con la venta del imán..

I ordered two packs of glue but received only one with a damaged pack. It's very bad and a shame on Amazon. We are paying in advance, and the product is not at the quality or missing or damaged sometimes higher in value than the market price.

جربت انواع كتير ، ده أفضل نوع. طبعا أغلى كتير من أي نوعية اشتريتها ، صناعة امريكي.